Pixhawk 2.4.8 Combo Kit – Advance

This PIXHAWK 2.4.8 Full Combo Kit consists of all-in-one required products for the drone flight controller. find all products included in this kit at below package includes.
PIXHAWK PX4 2.4.8 Flight Controller is a high-performance autopilot-on-module suitable for fixed-wing, multi-rotors, helicopters, cars, boats, and any other robotic platform that can move. It is targeted towards high-end research, amateur and industry need, and combines the functionality of the PX4FMU + PX4IO.
A new generation Ublox GPS NEO-M8N, with low power consumption and high precision, the ultimate accuracy is 0.6 meters, actually almost 0.9 meters, greater than the previous generation NEO-7N 1.4-1.6 meters accuracy; support GPS/QZSS L1 C/A, GLONASS L10F, BeiDou B1 protocol, and mode or more.
The GPS Folding Antenna Base mount comes will a laser-cut adhesive pad to quickly attach your GPS module, while the mount itself can be fixed to your craft using the base plate M3 hole, or the cross slides.

Pixhawk V2.4.8 Flight board:
The advanced 32-bit ARM CortexM4 high-performance processors can run NuttX RTOS real-time operating system
14 PWM / servo output
Bus interface (UART, I2C, SPI, CAN)
The integrated backup power and backup controller fail, the primary controller fails over to the backup control is safe
Provide automatic and manual modes
Provide redundant power input and failover
Multicolor LED lights
Provide a multi-tone buzzer Interface
Micro SD recording flight data

Processor:
32bit STM32F427 Cortex M4 core with FPU
168 MHz
128 KB RAM
2 MB Flash
32-bit STM32F103 failsafe co-processor

Sensors:
ST Micro L3GD20H 16 bit gyroscope
ST Micro X4HBA 303H 14-bit accelerometer/magnetometer
Invensense MPU 6000 3-axis accelerometer/gyroscope
MEAS MS5607 barometer

Interfaces:
5x UART (serial ports), one high-power capable, 2x with HW flow control
2x CAN (one with an internal 3.3V transceiver, one on expansion connector)
Spektrum DSM / DSM2 / DSM-X® Satellite compatible input
Futaba S.BUS® compatible input and output
PPM sum signal input
RSSI (PWM or voltage) input
I2C
SPI
3.3 and 6.6V ADC inputs
Internal micro USB port and external micro USB port extension

PIXHAWK PPM Encoder Module:
Support the input channels: 8
Output: PPM SUM × 1 / MUX × 1

Glass Fiber Flight Controller Anti-vibration/Shock absorber Set:
Color: Black
Material: Glass-fiber
Suit for the different open-source flight controllers, like APM 2.5/2.6/2.8, KK, MWC, and Pixhawk 2.4

NEO-M8N GPS Module:
Receiver type 72-channel Ublox M8 engine
GPS/QZSS L1 C/A, GLONASS L10F, BeiDou B1
SBAS L1 C/A: WAAS, EGNOS, MSAS
Galileo-ready E1B/C (NEO-M8N)
Nav. update rate1 Single GNSS: up to 18 HZ
Concurrent GNSS: up to 10Hz
Position accuracy2 2.0 m CEP
Acquisition2 Cold start: 26s
Aided starts: 2s
Reacquisition: 1.5s
Sensitivity2 Tracking & Nav: –167 dBm
Cold start: –148 dBm
Hot starts: –156 dBm
Assistance AssistNow GNSS Online
Assist Now GNSS Offline (up to 35 days)
Assist Now Autonomous (up to 6 days)
OMA SUPL & 3GPP compliant
Oscillator TCXO (NEO-M8N/Q)
Crystal (NEO-M8M)
RTC crystal Built-In
Noise figure On-chip LNA (NEO-M8M). Extra LNA for
lowest noise figure (NEO-M8N/Q)
Anti-jamming Active CW detection and removal
An extra onboard SAW bandpass filter (NEO-M8N/Q)
Memory ROM (NEO-M8M/Q) or Flash (NEO-M8N)
Supported antennas Active and passive
Odometer Travelled distance
Data-logger For position, velocity, and time (NEO-M8N)

GPS Folding Base Antenna set:
Material: CNC Aluminum alloy, carbon glass fiber rod
Mounting rod diameter: 4mm
length of rod: 14 cm.
GPS plate diameter: 40 mm
Base plate diameter: 35 mm
Mounting hole spacing: 16-35mm
Weight: 20g
Colour: Anodised black
Note: Adhesive Pad is not included

APM 2.5.2/2.6/2.8 Pixhawk Power Module V1.0:
Max input voltage: 28V
Max current sensing: 90A
Voltage and current measurement configured for 5V ADC
Switching regulator outputs 5.3V and 3A max
6-pos DF13 cable plugs directly to APM 2.5’s ‘PM’ connector
Support 6S battery.

Pixhawk OSD OLED Display
Product: OSD OLED Display
Operating voltage: 3.3V-5V DC
Compatible: Pixhawk 2.4.8 PIX PX4 Flight Control
Working temperature: -30°C ~ 70°C
Display dimension: 2.5 x 1.4 x 0.1mm
Over all dimension: 3 x 2.7 x 0.3mm
Weight: 3g

Pixhawk PPM Encoder Module
Support the input channels: 8
Output: PPM SUM × 1 / MUX × 1
Dimensions: 28 x 19 x 5 mm or 23 x 16 X 7
Weight: 12 gm. (containing all the input and output wires)

Package Included:
1x Pixhawk 2.4.8 PX4 32 Bit Flight Controller Kit
1x Anti-Vibration Shock Absorber for APM PixHawk
1x NEO-M8N ReadytoSky GPS Module with Compass for APM/Pixhawk
1x GPS Folding Metal Stand For APM & PIXHAWK
1x Power Module V6.0 Output BEC 3A XT60 for APM/Pixhawk